Carlos Alexandre dos Santos

pontifical catholic university of rio grande do sul

24H指数

113论文数

1.8K被引数

收录论文 26

发表时间

Influence of chromium content on the turning machinability of directionally solidified Al–7Si alloys 铬含量对定向凝固Al–7Si合金的车削加工性的影响

Journal of Manufacturing Processes

IF6.8

2026-09-22

PREAI

Maiquel Moraes Lopes; Richelli Pereira dos Santos; Gabriel Cirilo da Silva Simioni; Filipi Damasceno Vianna; Carlos Alexandre dos Santos

Effect of submicrometric and nanometric SiC particle addition on Mg MRI 230D alloy manufactured by stir-squeeze casting 通过搅拌挤压铸造制备的Mg MRI 230D合金中添加亚微米级和纳米级SiC粒子的影响

Journal of Materials Research and Technology-JMR&T

IF6.6

2026-08-26

OAAI

Igor Zimpel; Carlos Alexandre Dos Santos; Richard Silva Martins; Roges de Mari Leopoldo; Vinicius Karlinski de Barcellos

Influence of Different Cooling Rates on Grain Refinement and Tensile Strength of 38MnVS6 Microalloyed Steel after Hot Semiclosed-Die Forging

ACS OMEGA

IF4.3

2025-02-17

OAAI

Goulart, Guilherme O.; dos Santos, Carlos A.

Influence of Cu and Cr contents on the solidification path and microstructure formation of hypoeutectic as-cast Al-Cu-Cr alloys Cu和Cr含量对亚共晶al-cu-cr合金凝固路径和组织形成的影响

JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY

IF3.1

2023-07-17

PREAI

Elesbao, Denis Silva Grillo; Kakitani, Rafael; Cheung, Noe; Garcia, Amauri; de Barcellos, Vinicius Karlinski; da Costa, Eleani Maria; dos Santos, Carlos Alexandre

Effects of Sc Addition and Direct Aging Treatment on Microstructure and Hardness of AlSi10Mg Alloy

ADVANCED ENGINEERING MATERIALS

IF3.3

2023-07-05

PREAI

Martinez, Fellipe; dos Santos Junior, Carlos; Leal, Jaderson; Silva, Argos; Gouveia, Guilherme; Spinelli, Jose

Water-based lubricant containing protic ionic liquids and talc lubricant particles: Wear and corrosion analysis

WEAR

IF6.1

2023-04-01

PREAI

de Castro, Victor Velho; dos Santos, Leonardo Moreira; Antonini, Leonardo Marasca; Schroeder, Roberto Moreira; Mattedi, Silvana; Souza, Klester S.; Pereira, Marcelo Barbalho; Einloft, Sandra; dos Santos, Carlos Alexandre; Malfatti, Celia de Fraga

Engineering Design Process in Developing a Pin-on-Disk Apparatus to Perform Dry or Lubricated Sliding Wear Test

IEEE TRANSACTIONS ON INSTRUMENTATION AND MEASUREMENT

IF5.9

2023-01-01

PREAI

Simioni, Gabriel Cirilo da Silva; Pinheiro, Tiago de Vasconcellos; Vasques, Gustavo de Lima; Lantmann, Rafael Vieira; Lopes, Maiquel Moraes; Wettergreen, Matthew; Oden, Zillah Maria; Vianna, Filipi Damasceno; dos Santos, Carlos Alexandre

Electrochemical, mechanical, and tribological properties of corrosion product scales formed on X65 steel under CO2 supercritical pressure environments

SURFACE & COATINGS TECHNOLOGY

IF6.1

2022-09-01

PREAI

Bacca, Katryanne Rohana Georg; Lopes, Natalia Feijo; Batista, Giovanni dos Santos; dos Santos, Carlos Alexandre; da Costa, Eleani Maria

Investigation on machinability in turning of as-cast and T6 heat-treated Al-(3,7,12%)Si-0.6%Mg alloys 铸态和T6热处理Al-(3,7，12%)Si-0.6% Mg合金车削加工性能的研究

JOURNAL OF MANUFACTURING PROCESSES

IF6.8

2022-03-01

PREAI

Machado, Pedro Augusto Bottlender; Quaresma, Jose Maria do Vale; Garcia, Amauri; dos Santos, Carlos Alexandre

Microstructure, Hardness, Tensile Strength, and Sliding Wear of Hypoeutectic Al-Si Cast Alloys with Small Cr Additions and Fe-Impurity Content

ADVANCED ENGINEERING MATERIALS

IF3.3

2021-03-08

OAAI

de Rosso, Eduardo; dos Santos, Carlos A.; Garcia, Amauri

The effects of Cr addition on microstructure, hardness and tensile properties of as-cast Al-3.8wt.%Cu-(Cr) alloys Cr对铸态Al-3.8wt % Cu-(Cr) 合金显微组织、硬度和拉伸性能的影响

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T

IF6.6

2020-05-01

OAAI

Ribeiro, Thiago M.; Catellan, Eduardo; Garcia, Amauri; dos Santos, Carlos A.

Dendritic Spacing/Columnar Grain Diameter of Al-2Mg-Zn Alloys Affecting Hardness, Tensile Properties, and Dry Sliding Wear in the As-Cast/Heat-Treated Conditions

ADVANCED ENGINEERING MATERIALS

IF3.3

2020-01-27

PREAI

Ache, Carolina; Lopes, Maiquel; Reis, Bernardo; Garcia, Amauri; dos Santos, Carlos

Effect of solid fraction on microstructures and mechanical properties of a Mg-Al-La-Ca alloy processed by rheocasting

JOURNAL OF ALLOYS AND COMPOUNDS

IF6.3

2019-03-01

PREAI

Bartex, Sergio L. T.; dos Santos, Carlos A.; de Barcellos, Vinicius K.; Schaeffer, Lirio

The correlation of microstructure features, dry sliding wear behavior, hardness and tensile properties of Al-2wt%Mg-Zn alloys

JOURNAL OF ALLOYS AND COMPOUNDS

IF6.3

2018-10-01

OAAI

Reis, Bernardo P.; Lopes, Maiquel M.; Garcia, Amauri; dos Santos, Carlos A.

Austempering heat treatments of ductile iron using molten metal baths

MATERIALS AND MANUFACTURING PROCESSES

IF4.7

2018-01-16

PREAI

de Souza, Bruno Vaz; Ribeiro, Thiago Mugica; Francois, Aoutin; dos Santos, Carlos Alexandre

Lubricated sliding wear of SAE 1045 and SAE 52100 steel against alumina in the presence of biodiesel, diesel and a 50:50 blend of those fuels

WEAR

IF6.1

2016-12-01

OAAI

de Castro, Victor Velho; Mazzini Fontoura, Luiz Antonio; Benfica, Juliano Dornelas; Seferin, Marcus; Pacheco, Joyson Luiz; dos Santos, Carlos Alexandre

Performance and emission evaluations in a power generator fuelled with Brazilian diesel and additions of waste frying oil biodiesel

APPLIED THERMAL ENGINEERING

IF6.9

2016-04-01

OAAI

de Paulo, Anderson Antunes; da Costa, Ronaldo Silvestre; Rahde, Sergio Barbosa; Dalla Vecchia, Felipe; Seferin, Marcus; dos Santos, Carlos Alexandre

The Influence of Austempering Conditions on the Machinability of a Ductile Iron 等温淬火条件对球墨铸铁可加工性的影响

MATERIALS AND MANUFACTURING PROCESSES

IF4.7

2016-01-29

PREAI

Werlang Filho, Armindo; de Souza, Bruno Vaz; dos Santos, Carlos Alexandre