Salah Addin Burhan Al-Omari

united arab emirates university

H指数:23

被引数:1,652

个人简介

暂无内容

教育背景

暂无内容

工作经历

暂无内容

荣誉奖项

暂无内容

Improving performance and hydrogen knock limit in SI engines using acetone–gasoline blends

使用丙酮-汽油混合燃料提高SI发动机的性能和抗氢气爆震极限

International Journal of Hydrogen Energy

IF8.3

2025-12-020

PRE

Effect of gasoline injection pressure and CO2 dilution on the hydrogen knock limit extension in a Hydrogen-Gasoline dual-fuel engine

汽油喷射压力和CO2稀释对氢气汽油双燃料发动机中氢气爆震极限扩展的影响

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY

IF8.3

2025-03-011

PRE

Impact of intake air pressure and temperature on performance and hydrogen knock limit in a spark-ignition engine using Hydrogen-Gasoline blends

APPLIED THERMAL ENGINEERING

IF6.9

2025-03-012

PRE

Design and performance assessment of a triply-periodic-minimal-surface structures-enhanced gallium heat sink for high heat flux dissipation: A numerical study

APPLIED THERMAL ENGINEERING

IF6.9

2024-12-013

PRE

Experimental investigation on the influence of gasoline injection pressure on the hydrogen knock limit and performance of a hydrogen-gasoline dual fuel engine

汽油喷射压力对氢-汽油双燃料发动机氢爆震极限及性能影响的试验研究

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY

IF8.3

2024-09-013

PRE

Efficient processed carbon Soot@MoS2 hybrid Bi-functional electrode for dye-sensitized solar cell and asymmetric supercapacitor devices

NANO MATERIALS SCIENCE

IF17.9

2024-08-018

OAAI

Direct Z-scheme heterojunction impregnated MoS2-NiO-CuO nanohybrid for efficient photocatalyst and dye-sensitized solar cell

SCIENTIFIC REPORTS

IF3.9

2024-06-2410

OAAI

Flow structure and heat transfer characteristics of sweeping and steady impingement jets with/without chevrons on a semi-circular concave surface

PHYSICS OF FLUIDS

IF4.3

2024-06-041

PRE

Experimental investigation of the effect of CO2 dilution on the performance and hydrogen knock limit of a hydrogen-gasoline dual fuel spark ignition engine 1

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY

IF8.3

2024-05-017

PRE

Experimental investigation of spark timing on extension of hydrogen knock limit and performance of a hydrogen-gasoline dual-fuel engine

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY

IF8.3

2024-01-0111

PRE

Enhanced pursuance of dye-sensitized solar cell for indoor and outdoor stability using reduced graphene oxide @ Mn2O3 nanocomposite

使用还原的氧化石墨烯 @ Mn2O3纳米复合材料增强对染料敏化太阳能电池的室内和室外稳定性的追求

CARBON LETTERS

IF5.8

2023-12-095

PRE

A comparison of oscillating sweeping jet and steady normal jet in cooling gas turbine leading edge: Numerical analysis

冷却燃气轮机前缘的振荡扫掠射流和稳态正常射流的比较: 数值分析

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER

IF5.8

2023-07-0119

PRE

Architected lattices embedded with phase change materials for thermal management of high-power electronics: A numerical study

APPLIED THERMAL ENGINEERING

IF6.9

2023-01-0132

PRE

CI engine performance and emissions with waste cooking oil biodiesel boosted with hydrogen supplement under different load and engine parameters

ALEXANDRIA ENGINEERING JOURNAL

IF6.8

2022-06-0129

OAAI

Thermal management characteristics of a counter-intuitive finned heat sink incorporating detached fins impregnated with a high thermal conductivity-low melting point PCM

INTERNATIONAL JOURNAL OF THERMAL SCIENCES

IF5

2022-05-0126

PRE

Nature-inspired triply periodic minimal surface-based structures in sheet and solid configurations for performance enhancement of a low-thermal-conductivity phase-change material for latent-heat thermal-energy-storage applications

INTERNATIONAL JOURNAL OF THERMAL SCIENCES

IF5

2022-03-0135

PRE

A heat sink integrating fins within high thermal conductivity phase change material to cool high heat-flux heat sources

INTERNATIONAL JOURNAL OF THERMAL SCIENCES

IF5

2022-02-0135

PRE

On the effect of porosity and functional grading of 3D printable triply periodic minimal surface (TPMS) based architected lattices embedded with a phase change material

关于嵌入相变材料的基于3D可打印三重周期最小表面 (TPMS) 的架构的孔隙率和功能分级的影响

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER

IF5.8

2022-02-0177

PRE

Thermal characterization of 3D-Printed lattices based on triply periodic minimal surfaces embedded with organic phase change material

CASE STUDIES IN THERMAL ENGINEERING

IF6.4

2021-10-0152

OAAI

Using triply periodic minimal surfaces (TPMS)-based metal foams structures as skeleton for metal-foam-PCM composites for thermal energy storage and energy management applications

INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER

IF6.4

2021-05-01105

PREAI

Salah Addin Burhan Al-Omari

个人简介

教育背景

工作经历

荣誉奖项

研究方向