Ömer Keleş - Publications, H-index & Citations

Ömer Keleş

Gazi University

17H指数

51论文数

709被引数

收录论文 12

发表时间

Hot Stamping Techniques-A Study on Aerospace Ti6Al4V Sheet Metal Parts 热冲压技术——航空航天Ti6Al4V板材零件的研究

Iranian Journal of Science and Technology-Transactions of Mechanical Engineering

IF1.7

2026-08-01

PREAI

Aydogan, Cahit Sertac; Keles, Omer

Laser cutting of rectangular geometry into aluminum alloy: Effect of cut sizes on thermal stress field

OPTICS AND LASERS IN ENGINEERING

IF3.7

2014-10-01

PREAI

Akhtar, Sohail; Kardas, Omer Ozgur; Keles, Omer; Yilbas, Bekir Sami

The ballistic performance of SiC-AA7075 functionally graded composite produced by powder metallurgy

MATERIALS & DESIGN

IF7.9

2014-04-01

PREAI

Ubeyli, Mustafa; Balci, Erhan; Sarikan, Bertan; Oztas, M. Kemal; Camuscu, Necip; Yildirim, R. Orhan; Keles, Omer

Laser cutting of triangular blanks from thick aluminum foam plate: Thermal stress analysis and morphology

APPLIED THERMAL ENGINEERING

IF6.9

2014-01-01

PREAI

Yilbas, Bekir Sami; Akhtara, Sohail; Keles, Omer

Laser hole cutting in aluminum foam: Influence of hole diameter on thermal stress

OPTICS AND LASERS IN ENGINEERING

IF3.7

2013-01-01

PREAI

Yilbas, B. S.; Akhtar, S. S.; Keles, O.

Ballistic impact performance of an armor material consisting of alumina and dual phase steel layers

MATERIALS & DESIGN

IF7.9

2011-03-01

PREAI

Ubeyli, Mustafa; Deniz, Huseyin; Demir, Teyfik; Ogel, Bilgehan; Gurel, Bayram; Keles, Omer

Investigation on the ballistic performance of a dual phase steel against 7.62 mm AP projectile

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

IF7

2010-03-01

PREAI

Ubeyli, Mustafa; Demir, Teyfik; Deniz, Hueseyin; Yildirim, R. Orhan; Keles, Omer

Wedge cutting of mild steel by CO2 laser and cut-quality assessment in relation to normal cutting

OPTICS AND LASERS IN ENGINEERING

IF3.7

2008-10-01

PREAI

Yilbas, B. S.; Karatas, C.; Uslan, I.; Keles, O.; Usta, Y.; Yilbas, Z.; Ahsan, M.

Electrochemical properties of the laser nitrided surfaces of Ti-W-4V alloy

SURFACE & COATINGS TECHNOLOGY

IF6.1

2006-10-01

PREAI

Yibas, B. S.; Khaled, M.; Karatas, C.; Uslan, I.; Keles, O.; Usta, Y.; Ahsan, M.

CO2 laser gas assisted nitriding of Ti-6Al-4V alloy

APPLIED SURFACE SCIENCE

IF6.9

2006-10-01

PREAI

Yibas, B. S.; Karatas, C.; Uslan; Keles, O.; Usta, I. Y.; Ahsan, M.

Laser cutting of steel sheets: Influence of workpiece thickness and beam waist position on kerf size and stria formation

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

IF7.5

2006-02-01

PREAI

Karatas, C; Keles, O; Uslan, I; Usta, Y

Theoretical and experimental investigation of a pulse-width modulated digital hydraulic position control system

CONTROL ENGINEERING PRACTICE

IF4.6

2002-06-01

PREAI

Keles, O; Ercan, Y

研究方向